1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

New Pulley, Fitting And Woodruff Key Question

Discussion in 'Flat Fender Tech' started by Buster1, Oct 10, 2021.

  1. Oct 10, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Hey guys,

    I removed my grill, and radiator and got the old bent crank pulley out. Cleaning up the TC and got my new seals, etc.

    Here’s the question. The old pulley was snug, but came off by hand. I’ve got an identical stamped new pulley, but the groove is too tight for the woodruff key. I am test fitting first before getting my seals ready and such and the new pulley has to be gently tapped to seat it, and the woodruff key is cutting a very (very) small groove in the groove. Is this normal? I tapped it on a little, removed it, checked and filed the burrs in the groove, then repeated.

    But now, My new rookie issue is that my pulley is stuck on the shaft. The TC is on the bench being cleaned and prepped. Going to get a puller and remove the pulley, but it is so tight on the key.

    Any advice?

    Thanks.
    FA20B062-5166-42F0-8BFD-F03FF2D03E03.jpeg
     
  2. Oct 10, 2021
    Jeepenstein

    Jeepenstein Me like Jeep..

    North Central FL
    Joined:
    Jun 15, 2003
    Messages:
    2,132
    Slip it on without the key and use the backside of a dial caliper to measure the height of the keyway, swap to the other pulley and compare.. Compare that to your key and file/stone your key to fit..
     
  3. Oct 14, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Thank you.

    I got a pulley puller and got it off, then started filing and prepping both the key and the pulley groove… and now the pulley is stuck again! I’ve damaged it beyond repairing trying to remove it. It’s still stuck on there.

    I’m so frustrated right now.

    Does anyone have any other removal techniques? My puller is at its limit. I’m tapping all around the pulley and trying everything. Maybe some heat on it?

    thanks guys.
     
  4. Oct 14, 2021
    w3srl

    w3srl All-around swell dude Staff Member

    Port Orange, FL
    Joined:
    Nov 6, 2002
    Messages:
    4,275
    If the cover is still off you can use heat without worrying about damaging the seal. If not, you might want to have another seal ready just in case.
     
  5. Oct 14, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Cover is off. I’m attempting to “dry fit” the offending pulley before re-sealing everything. I’m thinking too that I need to get a torch and heat up the center of the pulley. It’s definitely stuck on the woodruff key, and will not seat. A few taps with a large socket and it’s like it’s welded to the crankshaft! :cry:
     
  6. Oct 15, 2021
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    Using heat to overcome an interference fit seems like a mistake. Suspect you'd never get it apart again.

    I would try honing the inside of the pulley first. As long as there is no radial sloppiness, and it all fits together, it should be fine. An abrasive hone sold for brake cylinder repair would be fine for that. I'd also polish the crank end with crocus cloth, to remove any roughness.

    https://www.amazon.com/CTA-Tools-1140-8-Inch-Cylinder/dp/B003553F54?th=1
     
  7. Oct 15, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Pulley is off! 15 seconds with the torch (on the pulley slot area) and under tension with the puller… came right off. Finally!!!

    Good points Timgr. Now I need to figure out how to fit a new pulley without having to beat it into place. The offending pulley slot was slightly narrower than the woodruff…

    … lesson learned for this rookie.
     
  8. Oct 15, 2021
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    On the next new pulley try the key in it before slipping it on the shaft, if the slot is too narrow (carefully!) use a file to widen it until the key does fit.
     
  9. Oct 15, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Absolutely! Good advice!
     
  10. Oct 15, 2021
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,622
    Stick with it. It's how you end up with a great Jeep. Stuff like this is frustrating but part of the learning process.
     
  11. Oct 16, 2021
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    If I could sell my experience for what it cost me, I'd be a wealthy man. But yeah.
     
    Fireball and Twin2 like this.
  12. Dec 15, 2021
    52M38-73CJ5

    52M38-73CJ5 Member

    Wenatchee WA
    Joined:
    Nov 11, 2020
    Messages:
    154
  13. Dec 17, 2021
    Buster1

    Buster1 New Member

    Ft Worth
    Joined:
    Aug 8, 2021
    Messages:
    49
    Thanks but I think that’s the water pump pulley. But I appreciate the help.

    I did get a new crank pulley and got it installed a while back, seems to be holding okay. The inside diameter of the replacement was also causing the pulley to bind on my crankshaft. Some light filing on the pulley allowed it to fit just right!
     
    ojgrsoi likes this.
  14. Dec 17, 2021
    Oldpappy

    Oldpappy A.C. Fults - Curmudgeon at large 2022 Sponsor

    East Tennessee
    Joined:
    Feb 8, 2021
    Messages:
    1,620
    I have had to hone the inside of two new crankshaft pulleys I have used lately, and often have to use a stone on new woodruff keys for these or back axles. Like already mentioned I use a brake cylinder hone to polish the bore a little.
     
New Posts