1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by BrettM0352

  1. BrettM0352
    Post

    The Official "What The Heck Is This?" Thread

    I set up my e-brake and clutch linkage today, and this bracket is still empty. What is it for? [IMG] [IMG]
    Post by: BrettM0352, Sep 30, 2017 in forum: Early CJ5 and CJ6 Tech
  2. BrettM0352
    Post

    Is this what I think it is?

    I'm not even sure the boss knows it's laying out there, let alone what it came from. The other guy I work with who has been around for 10 years...
    Post by: BrettM0352, Sep 21, 2014 in forum: Early Jeep Restoration and Research
  3. BrettM0352
    Post

    Is this what I think it is?

    Is the overdrive adaptable to a d18? I would however like to keep my PTO winch setup.
    Post by: BrettM0352, Sep 21, 2014 in forum: Early Jeep Restoration and Research
  4. BrettM0352
    Thread

    Is this what I think it is?

    I found this in the back of my shop in the scrap yard connected to a transmission. [IMG]
    Thread by: BrettM0352, Sep 19, 2014, 11 replies, in forum: Early Jeep Restoration and Research
  5. BrettM0352
    Post

    Second Chance: Texas 1965 CJ5

    the further I get inside of this JEEP the more amazed I am at the condition of this thing. I spent a few hours today knocking off all the years of...
    Post by: BrettM0352, Sep 1, 2014 in forum: Builds and Fabricators Forum
  6. BrettM0352
    Post

    Second Chance: Texas 1965 CJ5

    Got the engine broken loose last week. The cylinder walls looks great after cleaning them up with a scotch pad and some 1500 grit. [IMG] I just...
    Post by: BrettM0352, Aug 25, 2014 in forum: Builds and Fabricators Forum
  7. BrettM0352
    Post

    Second Chance: Texas 1965 CJ5

    To be honest, that's the question I've been asking myself as well. Taking the tub off an early CJ is much less invasive than a later model which...
    Post by: BrettM0352, Aug 18, 2014 in forum: Builds and Fabricators Forum
  8. BrettM0352
    Thread

    Second Chance: Texas 1965 CJ5

    It's been a long time since I've come around these parts, I've been learning in my short 25 years of life that life has a funny way of taking you...
    Thread by: BrettM0352, Aug 14, 2014, 10 replies, in forum: Builds and Fabricators Forum
  9. BrettM0352
    Post

    LJ prices in your area...

    ~$16k from the dealership for a 2006 Rubicon, 100,000 miles, last time I saw one in Eastern NC
    Post by: BrettM0352, Jun 15, 2013 in forum: Quitters' Club
  10. BrettM0352
    Post

    1972 CJ-5 Almost Restoration

    I haven't started my engine yet so I can't say if mine needs adjusting.
    Post by: BrettM0352, Jan 15, 2013 in forum: Builds and Fabricators Forum
  11. BrettM0352
    Post

    1972 CJ-5 Almost Restoration

    I feel you on the live wires. I finally got mine wrestled into this fashion: [IMG] [IMG]
    Post by: BrettM0352, Jan 14, 2013 in forum: Builds and Fabricators Forum
  12. BrettM0352
    Post

    floor supports

    No, They go through the top of the floor pans.
    Post by: BrettM0352, Jan 12, 2013 in forum: Intermediate CJ-5/6/7/8
  13. BrettM0352
    Thread

    Cowl Vent - No Heater

    For those of yall who don't run a heater system, what are yall doing for the cowl vent? I was thinking about just putting a a piece of sheet steel...
    Thread by: BrettM0352, Jan 11, 2013, 10 replies, in forum: Intermediate CJ-5/6/7/8
New Posts