1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. dirty Bakers
    Post

    BAD new leaf springs. With Pics :(

    That sucks.
    Post by: dirty Bakers, Oct 30, 2011 in forum: Intermediate CJ-5/6/7/8
  2. dirty Bakers
    Post

    67 CJ-5..... 2 yrs or less build

    Keep workin hard.
    Post by: dirty Bakers, Oct 30, 2011 in forum: Builds and Fabricators Forum
  3. dirty Bakers
    Post

    My new project

    Post by: dirty Bakers, Oct 29, 2011 in forum: Builds and Fabricators Forum
  4. dirty Bakers
    Post

    Powered Willys Trailers

    Both Land-Rover and Volvo developed these trailers and as far as I know Vovo produced quit a few....
    Post by: dirty Bakers, Oct 10, 2010 in forum: Jeep Trailer Tech
  5. dirty Bakers
    Post

    front and rear wheel seals.

    If you are in arizona contact BMI Off-road we are steeped in working on the classic cjs.
    Post by: dirty Bakers, Apr 11, 2009 in forum: Early CJ5 and CJ6 Tech
  6. dirty Bakers
    Post

    front axle upgrade question

    Thanks. If I were to go to a salvage yard what years would be good candidates?
    Post by: dirty Bakers, Mar 8, 2009 in forum: Early CJ5 and CJ6 Tech
  7. dirty Bakers
    Thread

    front axle upgrade question

    Is there an open knuckle front axle that would be a good swap for my 1960 CJ5? I want to improve my steering starting with the axle.
    Thread by: dirty Bakers, Mar 8, 2009, 7 replies, in forum: Early CJ5 and CJ6 Tech
  8. dirty Bakers
    Post

    Blinker switch relocation

    thats a good idea thanks.
    Post by: dirty Bakers, Mar 6, 2009 in forum: Early CJ5 and CJ6 Tech
  9. dirty Bakers
    Thread

    Blinker switch relocation

    I want to move my turn signal switch to the dash so when I'm wheeling I dont hit my hand on the turn signal lever again. Has any one done this....
    Thread by: dirty Bakers, Mar 5, 2009, 4 replies, in forum: Early CJ5 and CJ6 Tech
  10. dirty Bakers
    Post

    Ford Reverse Rotation Steering Box Install

    Do you have to cut the sroud? what about the p.t.o. propeller shaft?
    Post by: dirty Bakers, Feb 16, 2009 in forum: Early CJ5 and CJ6 Tech
  11. dirty Bakers
    Post

    diesel cj engine

    Are you selling it? What are you asking for it?
    Post by: dirty Bakers, Feb 15, 2009 in forum: Early CJ5 and CJ6 Tech
  12. dirty Bakers
    Post

    Dana 44 rebuild, finally ready to order parts, need a little help

    Do the flanges separate from the axles shafts? Are the grease zurks at each end of the axle tubes?
    Post by: dirty Bakers, Feb 15, 2009 in forum: Early CJ5 and CJ6 Tech
  13. dirty Bakers
    Post

    propeler shaft angle dangle

    well the body is off at the moment.
    Post by: dirty Bakers, Feb 10, 2009 in forum: Early CJ5 and CJ6 Tech
  14. dirty Bakers
    Thread

    propeler shaft angle dangle

    This is on our '60. It has 2" rancho springs (not my favorite) and degree wedges. Is that a 30 deg. angle? I didn't check but I should have....
    Thread by: dirty Bakers, Feb 10, 2009, 10 replies, in forum: Early CJ5 and CJ6 Tech
  15. dirty Bakers
    Post

    Dana 44 advantages

    I would just have them Finnish the job if they have it apart. If you have them put it back together and take it somewhere else they are going to...
    Post by: dirty Bakers, Feb 10, 2009 in forum: Early CJ5 and CJ6 Tech
  16. dirty Bakers
    Post

    1960 cj5 willys paint color

    I just searched for 1960 jeep universal vehicles paint chips and I got what I needed to know. JLb
    Post by: dirty Bakers, Feb 8, 2009 in forum: Early Jeep Restoration and Research
  17. dirty Bakers
    Post

    axle shims

    thanks guys thats just what I needed too.
    Post by: dirty Bakers, Feb 8, 2009 in forum: Early CJ5 and CJ6 Tech
  18. dirty Bakers
    Post

    Talk me outta this guys!

    I will buy the springs from you.
    Post by: dirty Bakers, Jan 27, 2009 in forum: Early CJ5 and CJ6 Tech
  19. dirty Bakers
    Post

    Those square nuts w/ the clips used on body panels

    Thank you for the help muchachos!:flag:
    Post by: dirty Bakers, Jan 27, 2009 in forum: Early CJ5 and CJ6 Tech
  20. dirty Bakers
    Thread

    Those square nuts w/ the clips used on body panels

    I need some for my floor pan. Where the heck do you get those things?
    Thread by: dirty Bakers, Jan 25, 2009, 16 replies, in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2
New Posts