1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

What Did You Do To Your Jeep Today?

Discussion in 'Builds and Fabricators Forum' started by Focker, Jul 23, 2016.

  1. sterlclan

    sterlclan Member 2024 Sponsor 2022 Sponsor

    no pics sorry.... yup posi is a trac loc that's just the name they gave it, its a clutched rear differential. my jeep is a 74
     
  2. Rich M.

    Rich M. Shoe salesman 2024 Sponsor 2023 Sponsor 2022 Sponsor

    I now know why ps fluid runs all over the floor. The rebuilder left the high pressure o ring out between the pump and body....
    IMG_20190630_150634987~2.jpg
     
  3. Rich M.

    Rich M. Shoe salesman 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Speaking of "beep beep"
    IMG_20190630_165220609~2.jpg IMG_20190630_171757773~3.jpg
     
    3b a runnin and Lockman like this.
  4. Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Nice, Man
    Yep... Gotta have that in there. Just redid mine . No Leaks, Bled it , & ran it through its positions ... side to side. :)
     
    Last edited: Jun 30, 2019
  5. masscj2a

    masscj2a Member 2023 Sponsor

    We're you letting it stand in the water to take a leak ? When you get old, sometimes it's necessary.
     
    dozerjim and Norcal69 like this.
  6. 3b a runnin

    3b a runnin Active Member 2023 Sponsor 2022 Sponsor

    HaHa No, took care of that in the bushes just after the pic. Not much of a turning place, so I got its feet wet.
     
    dozerjim and masscj2a like this.
  7. Dave B

    Dave B Frankenjeep '67

    I "occasionally" forgot to cancel my non-canceling turn signal, so have been planning on adding a buzzer.

    Done today! --an Icstation DC 12V 85db Active Piezo Electronic Buzzer Beep Tone (that's what's written on the pkg.:D) Couldn't find them locally, so had to go Amazon for a package of 2 for $7.99 (with free shipping)

    Simply tinned/soldered the tips of the wires so they would be a little rigid and "plugged" it into my flasher--black to L and red to X. Then I covered the grill of the buzzer with two layers of bath-towel cut to size and taped it on the flasher body. Works great, plenty loud--heard above any road or engine noise.

    [​IMG]

    Below--you can see a slight edge of the purple bath-towel "volume-suppressing material" under the wrap-around tape.
    [​IMG]
     
    Last edited: Jul 3, 2019
  8. Focker

    Focker That's a terrible idea...What time? Staff Member

    Cool idea. Would you be able to post a YouTube video?
     
  9. TIm E

    TIm E Aggressively average

    fhoehle, FinoCJ, Rich M. and 4 others like this.
  10. Dave B

    Dave B Frankenjeep '67

    Not capable of posting a video for post #1680 regarding a turn signal buzzer, but think forklift/equipment backup alarm for sound. Still plenty loud with a volume-suppressing wrap on it. May need more suppression. I just got back from a run to a very busy July 3rd town and the "beep, beep" could draw attention. :rolleyes:
     
    Focker likes this.
  11. homersdog

    homersdog Tulsa, Ok 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Cheapo steering wheel cover, 1978 ish
    [​IMG]

    Cheapo steering wheel cover, 2019
    [​IMG]
     
  12. Jw60

    Jw60 That guy 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Add a Rheostat or trial and error with resistors?
     
  13. Dave B

    Dave B Frankenjeep '67

    I have a couple of resistors from a junk headphone that I'll try to reduce the buzzer volume with or, better yet, I might use one of the headphone slider volume controls. Thanks for the thought!
     
    Last edited: Jul 5, 2019
  14. Boyink

    Boyink Super Moderator Staff Member

    jeep-armrest - 1.jpg

    Got tired of burning my arm on the armrest lock cylinder...didn't like any of the aftermarket armrest covers...so just got some fabric at Walmart. Didn't want just black because it would heat up, couldn't match the Sahara green, all the tan looked like it would just get dirty.

    Not sure how much I like this yet, but easy enough to re-do down the road.
     
  15. neohic

    neohic Gentleman Jeepist

    Guy at work bought himself a “1970” but it’s pretty cut up. Drove in today just to park them next to each other.

    [​IMG]

    ... bookends. :lol:
     
  16. FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    definitely remember seeing that one on CL...Doug may have posted in on here even...
     
  17. Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Here's the old rigid line , that was hitting the motor mount when pivoting to tighten my P.S. belt. It was routed under the P.S. reservoir.
    Existing PS Rigid Line.JPG
    Here's what I did today.... Miss's motor mount by almost 2 " now.
    New Flex Pressure line.JPG
     
  18. neohic

    neohic Gentleman Jeepist

    The seller had been sitting on it for a while. I think he got it for an okay price for the parts that are in it. It’s definitely a “one piece at a time” special.
     
  19. homersdog

    homersdog Tulsa, Ok 2024 Sponsor 2023 Sponsor 2022 Sponsor

    I hope you encourage him to join us here!
     
    ojgrsoi likes this.
  20. neohic

    neohic Gentleman Jeepist

    Already done!