1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Activity

Activity stream for all registered members at ECJ5.

  1. truckee4x4 liked Howard Eisenhauer's post in the thread Cj5 Master Cylinder Stuck.

    If the m/c piston doesn't return all the way to the rear stop then the ports to the reservoir don't get uncovered diss-allowing fluid to...

    Jan 28, 2022 at 1:06 AM
  2. PeteL replied to the thread A Couple Of 2a's At The Edge Of The Earth, Mt.

    F-heads fer sher.

    Jan 28, 2022 at 12:16 AM
  3. Rozcoking23 liked timsresort's post in the thread '65 Rubicon Rig.

    We decided to start at the front floor with that dimension, and move back. So the first cross bar is the lower windshield bar. A cut, 2...

    Jan 28, 2022 at 12:07 AM
  4. amboynut replied to the thread Get Cerlist Running.

    Excellent! I'll be in touch via PM when I'm headed your way. tb

    Jan 28, 2022 at 12:06 AM
  5. Ol Fogie liked Howard Eisenhauer's post in the thread Cj5 Master Cylinder Stuck.

    If the m/c piston doesn't return all the way to the rear stop then the ports to the reservoir don't get uncovered diss-allowing fluid to...

    Jan 27, 2022 at 11:54 PM
  6. Ol Fogie liked timsresort's post in the thread '65 Rubicon Rig.

    We decided to start at the front floor with that dimension, and move back. So the first cross bar is the lower windshield bar. A cut, 2...

    Jan 27, 2022 at 11:52 PM
  7. Ol Fogie liked Fireball's post in the thread 71 Wheeling Rig.

    Yeah, that's coming off the bench with the engine hoist.

    Jan 27, 2022 at 11:45 PM
  8. Ol Fogie liked Fireball's post in the thread 71 Wheeling Rig.

    Got the shaft and bearing swapped out: [IMG] Bolted the planetary assembly to the transmission output shaft. Lucky for me a D18 yoke...

    Jan 27, 2022 at 11:44 PM
  9. SFaulken liked Jw60's post in the thread Tips For Starting Up A Rebuilt Engine With Sniper Efi.

    The issue with the sniper is the computer processes fast enough to see the ignition firing 90,150,90,150 90,150 degrees of crank...

    Jan 27, 2022 at 11:38 PM
  10. Howard Eisenhauer replied to the thread Cj5 Master Cylinder Stuck.

    If the m/c piston doesn't return all the way to the rear stop then the ports to the reservoir don't get uncovered diss-allowing fluid to...

    Jan 27, 2022 at 11:37 PM
  11. ITLKSEZ replied to the thread WTB 10 Spline U-joint Yoke.

    I might have one or two. I’ll check in the morning.

    Jan 27, 2022 at 11:29 PM
  12. truckee4x4 liked Jw60's post in the thread Tips For Starting Up A Rebuilt Engine With Sniper Efi.

    The issue with the sniper is the computer processes fast enough to see the ignition firing 90,150,90,150 90,150 degrees of crank...

    Jan 27, 2022 at 11:24 PM
  13. KJSR replied to the thread Cj5 Master Cylinder Stuck.

    Sounds like your rod going into the master cylinder is not adjusted properly. How much clearance is there in the rod before it hits the...

    Jan 27, 2022 at 11:19 PM
  14. Jw60 replied to the thread Tips For Starting Up A Rebuilt Engine With Sniper Efi.

    The issue with the sniper is the computer processes fast enough to see the ignition firing 90,150,90,150 90,150 degrees of crank...

    Jan 27, 2022 at 11:08 PM
Loading...
New Posts