1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Milestone

Discussion in 'Builds and Fabricators Forum' started by Howard Eisenhauer, Mar 30, 2014.

Page 1 of 2
  1. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Hit a major milestone today, after chasing a few funnies the wiring is working :)

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    H.
     
    Howard Eisenhauer, Mar 30, 2014
    #1
  2. Johns1967CJ5

    Johns1967CJ5 Sponsor

    Where do I get one of those stickers ? :)
     
    Johns1967CJ5, Mar 30, 2014
    #2
  3. 68BuickV6

    68BuickV6 Well-Known Member

    Tonka slowly lives?
     
    68BuickV6, Mar 30, 2014
    #3
  4. mb82

    mb82 I feel great!

    Nice
     
    mb82, Mar 30, 2014
    #4
  5. nickmil

    nickmil In mothballs.

    Very nice!!


    Sent from my iPhone
     
    nickmil, Mar 30, 2014
    #5
  6. bkd

    bkd Moderator Supreme Staff Member 2022 Sponsor

    Nice

    Sent from my SCH-I545 using Tapatalk
     
    bkd, Mar 30, 2014
    #6
  7. Unkel Dale

    Unkel Dale delivery on my Jeep from Ft. Campbell, Ky.

    That white is just brilliant, Good for you on the rewire being done.
    You show photos from the rear, with the sticker, does your body end up square, straight and flush with the rear cross member?
    I have to mount a replacement body this spring and I did NOT take photos. I took the old body off years ago.
     
    Unkel Dale, Mar 30, 2014
    #7
  8. 68BuickV6

    68BuickV6 Well-Known Member

    Rear crossmember does not sit square with the body.

    It's offset for the license plate.
     
    68BuickV6, Mar 30, 2014
    #8
  9. Long&Low

    Long&Low Active Member

    Looks good, luv the grave digger tires, nice restoration work.
     
    Long&Low, Mar 30, 2014
    #9
  10. 1967 CJ5A

    1967 CJ5A Mike 2024 Sponsor 2023 Sponsor 2022 Sponsor

    I like that light you have on the rear, any info on it?
     
    1967 CJ5A, Mar 30, 2014
    #10
  11. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    The one with the clear lens? Just a cheap set of flood lights I found at the store (other one went on the trailer).

    H.
     
    Howard Eisenhauer, Mar 31, 2014
    #11
  12. duffer

    duffer Rodent Power

    Looks good Howard. Man, you need to get some miles on Tonka. 29K and I suppose that's kmR)
     
    duffer, Mar 31, 2014
    #12
  13. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Nope, that's them old fashioned mile thingies they used back in the last century :twisted:

    Actually that's mileage since we got him back in '90, the speedo cable cable was disconnected somewheres around the 5 mile mark when he got zambonie-fied.:)

    H.
     
    Howard Eisenhauer, Mar 31, 2014
    #13
  14. tarry99

    tarry99 Member

    Wow............Very Nice.
     
    tarry99, Mar 31, 2014
    #14
  15. Quill

    Quill Member

    Looking real good.
     
    Quill, Mar 31, 2014
    #15
  16. rusty

    rusty Well-Known Member

    Great to see it getting back together . You will be driving it soon.
     
    rusty, Mar 31, 2014
    #16
  17. wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    fb Good deal. Looks great, too.
     
    wheelie, Mar 31, 2014
    #17
  18. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    More progress made- won't be long now :)


    Some of you may remember my take on a dual master cylinder installation-

    [​IMG]


    I finally, after *WAY* too much fabrication work, got the remote reservoir installed :)


    [​IMG]

    and plumbed-

    [​IMG]



    Now, at this point I'd like to say I *KNOW* I bought a &^%$ bleeder kit, I *KNOW* I saw the &^%$ bleeder kit not too long ago, but do you think I could *FIND* the &^%$ bleeder kit today? mehh

    Well, I got most of the air out, it will have to wait until I get some help for the rest of it. :rofl:

    Tomorrow it's the final electrical work & finish up rebuilding the vacuum wiper motors.



    That is all- please return to your regularly scheduled threads :)

    H.
     
    Howard Eisenhauer, Apr 12, 2014
    #18
  19. tarry99

    tarry99 Member

    Nice Job!
     
    tarry99, Apr 12, 2014
    #19
  20. davistroy

    davistroy Grasshopper

    Looks fantastic! Love the plumbing and wiring ... Looks better than professional.

    What do you call those brass fittings you have on the bottom of your MC? And where can I get two of em?
     
    davistroy, Apr 12, 2014
    #20
Page 1 of 2