1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Philip-TX

  1. Philip-TX
    Post

    Steering wheel making my hands black !?

    Not that I'd wish it on ANYBODY.... But if you had Ebola you could skate right into the US. :)
    Post by: Philip-TX, Oct 9, 2014 in forum: Early CJ5 and CJ6 Tech
  2. Philip-TX
    Post

    Steering wheel making my hands black !?

    The kind of paint used to paint refrigerators....
    Post by: Philip-TX, Oct 8, 2014 in forum: Early CJ5 and CJ6 Tech
  3. Philip-TX
    Post

    Steering wheel making my hands black !?

    I used appliance paint on mine no problems. I also did the JB weld cracking fixes..(in my build thread)
    Post by: Philip-TX, Oct 8, 2014 in forum: Early CJ5 and CJ6 Tech
  4. Philip-TX
    Post

    Removing spindle wheel bearing nut

    The end of the stud should have an "L" stamped in it. (At least my '59 does.)
    Post by: Philip-TX, Oct 8, 2014 in forum: Early CJ5 and CJ6 Tech
  5. Philip-TX
    Post

    Removing spindle wheel bearing nut

    Pic to go with Howard's 1000 words. :) [IMG]
    Post by: Philip-TX, Oct 8, 2014 in forum: Early CJ5 and CJ6 Tech
  6. Philip-TX
    Post

    Throttle and Choke Cable 1955 CJ5

    ^^^ You need to put one of these (cable stops) on the end of the cable. [IMG] available at FLAPS
    Post by: Philip-TX, Sep 23, 2014 in forum: Early CJ5 and CJ6 Tech
  7. Philip-TX
    Post

    Throttle and Choke Cable 1955 CJ5

    "Throttle" goes where the spring is hanging (in this pic)[IMG][
    Post by: Philip-TX, Sep 23, 2014 in forum: Early CJ5 and CJ6 Tech
  8. Philip-TX
    Post

    Garrett's "59 CJ5 Project

    Been a while but we have deployed the jeep at the farm. "Flat Fender Jeep Repair" Lewisville, TX got it running like a champ. (Hope...
    Post by: Philip-TX, Aug 11, 2014 in forum: Builds and Fabricators Forum
  9. Philip-TX
    Post

    North Texas CJ6

    Mark, I told my son to pause live TV for a little while...... Then we can pick it back up and fast fwd through the figure skating and watch the...
    Post by: Philip-TX, Feb 10, 2014 in forum: Builds and Fabricators Forum
  10. Philip-TX
    Post

    Distributor replacement problem

    OK just got an email from Kaiser mentioning the tab is offset on the shaft, and saying I might need to file it a bit. Maybe this will help...
    Post by: Philip-TX, Nov 6, 2013 in forum: Early CJ5 and CJ6 Tech
  11. Philip-TX
    Post

    Distributor replacement problem

    Not 180* out. rotor is in correct position in relation to the slot down in the oil pump. Doesn't seem like 180* would matter on slot alignment,...
    Post by: Philip-TX, Nov 5, 2013 in forum: Early CJ5 and CJ6 Tech
  12. Philip-TX
    Thread

    Distributor replacement problem

    1959 CJ5 F134 I got a solid state dist. from Kaiser that is supposed to be a direct drop-in. Well not so much. It will not seat the last...
    Thread by: Philip-TX, Nov 5, 2013, 11 replies, in forum: Early CJ5 and CJ6 Tech
  13. Philip-TX
    Post

    Defrost duct attachment question

    Haven't gotten to my heater system yet but I'd.... Look for some kinda adapter at the hardware store to get the Defroster down to the size of...
    Post by: Philip-TX, Sep 19, 2013 in forum: Early CJ5 and CJ6 Tech
  14. Philip-TX
    Post

    Exact size of tire for my CJ5

    I think this is what you are looking for (explains the numbers) http://www.tirerack.com/tires/tiretech/techpage.jsp?techid=46 Lots more tire...
    Post by: Philip-TX, Sep 18, 2013 in forum: Early CJ5 and CJ6 Tech
New Posts