1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by ocnorb

  1. ocnorb
    Post

    1971 CJ5 D44 Flanged Axles

    I have a flanged axle 44 in the Cj-3B I am working on. I will be selling the front and rear axles soon. Of course the shipping might be too...
    Post by: ocnorb, Dec 14, 2005 in forum: Early CJ5 and CJ6 Tech
  2. ocnorb
    Post

    Welcome to more Heater Talk

    Heated seats are the best!!!:) I can't believe noone has mentioned them. http://www.sportsimportsltd.com/afcarseathea.html
    Post by: ocnorb, Dec 4, 2005 in forum: Early CJ5 and CJ6 Tech
  3. ocnorb
    Post

    Axle Q's

    I don't have any right now as my digital camera and greasy paws don't mix well...... but I will try and get some for you. The only thing I would...
    Post by: ocnorb, Nov 24, 2005 in forum: Flat Fender Tech
  4. ocnorb
    Post

    Axle Q's

    I have turned down the hubs off of a 14 bolt truck axle to allow for 5x5.5" wheels and brake rotors. Weld the 14 bolt spindles to the Dana 44...
    Post by: ocnorb, Nov 23, 2005 in forum: Flat Fender Tech
  5. ocnorb
    Post

    Extending rear of frame on 72 CJ5???

    I would build a new frame from the 2x4 box. The original frame is c-channel, and I don't think that the box-to-c joint would be worth the risk. I...
    Post by: ocnorb, Nov 12, 2005 in forum: Builds and Fabricators Forum
  6. ocnorb
    Post

    rear gas tank

    I rolled a 2A with the underseat tank when I was 16 (long ago). The windsheild frame pinned me under it while the under seat tank proceeded to...
    Post by: ocnorb, Oct 30, 2005 in forum: Flat Fender Tech
  7. ocnorb
    Post

    Odd Fire HEI

    I have always been able to just walk in and get one. You do have me concerned a bit now though. I would like to hear from someone in the parts...
    Post by: ocnorb, Oct 24, 2005 in forum: Early CJ5 and CJ6 Tech
  8. ocnorb
    Post

    Somebody help before I burn this jeep!

    Could the lines be hooked up backwards??? Front to rear lines reversed?? I have had a few new MC's that were bad from the parts store. Exchange it...
    Post by: ocnorb, Oct 22, 2005 in forum: Early CJ5 and CJ6 Tech
  9. ocnorb
    Post

    Frame Question

    By the looks of those welds, you would have a time getting those off. I would just leave them on.
    Post by: ocnorb, Oct 20, 2005 in forum: Early CJ5 and CJ6 Tech
  10. ocnorb
    Post

    Crack pipe alert: Nissan Z24 engine swap?

    I drove my Cj-5 as a daily driver for 3 years, 31 miles each way, all freeway. It had 33x12.50's on 10"wheels.(not the best for DD's) I averaged...
    Post by: ocnorb, Oct 13, 2005 in forum: Flat Fender Tech
  11. ocnorb
    Post

    Really bad afternoon - hole in block

    You make some good points.:stout:
    Post by: ocnorb, Oct 4, 2005 in forum: Early CJ5 and CJ6 Tech
  12. ocnorb
    Post

    Building a frame..

    No jig- I just used levels and large squares to keep everything straight as possible.
    Post by: ocnorb, Oct 4, 2005 in forum: Builds and Fabricators Forum
  13. ocnorb
    Post

    Building a frame..

    HA, HA -- not as ambitious as you might think. I just couldn't see putting a ton of work into the rest of the Jeep if it had a bad frame. I have...
    Post by: ocnorb, Oct 4, 2005 in forum: Builds and Fabricators Forum
  14. ocnorb
    Post

    Building a frame..

    some more I have the intermediate crossmember in. The front and rear are held by temporary members to keep it aligned. [IMG] [IMG] [IMG]...
    Post by: ocnorb, Oct 3, 2005 in forum: Builds and Fabricators Forum
  15. ocnorb
    Thread

    Building a frame..

    I am resto-modding a '57 3B that belongs to my wife. (No she is not mail order bride R) ) The frame was cracked almost all of the way through at...
    Thread by: ocnorb, Oct 3, 2005, 14 replies, in forum: Builds and Fabricators Forum
New Posts