1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Once Again.. Show me pics of your saginaw to frame mount

Discussion in 'Early CJ5 and CJ6 Tech' started by DanStew, Jan 24, 2005.

  1. DanStew

    DanStew Preowned Merkin salesman Staff Member

    When i put in my waggie axles i will have to redo my saginaw mount on the frame since the box is too far back. Can you show me the monut you guys used to mount the saginaw box to the front frame. I know you need to box the frame, which i have done, than get a mount made and weld in holes in the fraem and sleeve them wuth tube to prevent the bolts from crushing the frame. I am confused on the fact that i saw a few mount photos and the bottom of the mount hangs below the frame and it looks like th ebox is only really on the frame in 2 places. So please let me see some pics :)
     
    DanStew, Jan 24, 2005
    #1
  2. mb82

    mb82 I feel great!

    dan just got mine in from Wr3sl... its from big daddy offroad. i placed it up to the frame and i think i will work with some minor mods.

    [​IMG]

    you can get it at bigdaddyoffroad.com


    sorry no pics since my comp died on me today and my parents computer does not reconize my camera.
     
    mb82, Jan 24, 2005
    #2
  3. DanStew

    DanStew Preowned Merkin salesman Staff Member

    I can use that mount now, but i am going to lose the front crossmember that the mount works with.
     
    DanStew, Jan 24, 2005
    #3
  4. JohnyJeep

    JohnyJeep BLOWING A XING NEAR U@2AM

    I'll look for pics of mine. I have the cast mount. It's like a factory style setup. Might be tomorrow.

    Edit:I found some.

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    Let me know if you need a more detailed or different pic Dan. ;)
     
    JohnyJeep, Jan 25, 2005
    #4
  5. DanStew

    DanStew Preowned Merkin salesman Staff Member

    Thanks Johhny. I see the cast monut bolts to the underside of theframe. I may try to locate a cast mount also.

    Thanks!
     
    DanStew, Jan 25, 2005
    #5
  6. w3srl

    w3srl All-around swell dude Staff Member

    That's the route I'm going Dan, look for one from a Commando. I'm planning to use the Commando mount, late CJ manual box/pitman arm and the modified tie rods from Herm with stock ends. Sorry no pics, it is just too durned cold to venture down to the garage. Mebbe once we break 10*! :rofl:
     
    w3srl, Jan 25, 2005
    #6
  7. 53Flattie

    53Flattie Intigator

    Steve - Is Herm selling the tie rod tubes, cut down and re-threaded to work with the Dana 25/27?

    Any idea on price.

    Sorry for the hijack Dan! Just to make up for it, I'll post some pictures fo the Sagi mount on the flattie when I get home tonight. :D
     
    53Flattie, Jan 25, 2005
    #7
  8. zed

    zed Iowa- Gateway to Nebraska

    johnny, whats your intermediate shaft from? universals? length spline counts on both ends? etc.

    it looks very close to what i am trying to find, build ( hatch, whatever)
     
    zed, Jan 25, 2005
    #8
  9. jd7

    jd7 Sponsor

    John, very nice setup. What size tubing did you use for the crossmember? Is it notched on the bottom. Once again nicely done.
     
    jd7, Jan 25, 2005
    #9
  10. JohnyJeep

    JohnyJeep BLOWING A XING NEAR U@2AM

    Zed: I'm not sure. This swap was done by a po. I think it's a postal jeep column. Hope these pics help a little.

    [​IMG]

    [​IMG]

    jd: IIRC it was either 1 1/2 or 1 1/4 DOM tubing. I made plates to box in the frame where the tubing goes through. It's not notched at all. Heres a pic of the old crossmember cut out and the new tubing and end plates.

    [​IMG]
     
    JohnyJeep, Jan 25, 2005
    #10
  11. w3srl

    w3srl All-around swell dude Staff Member

    Si Senor. $70 bux gets ya brand new tubes cut to the correct length and threaded to accept the stock TREs, thus eliminating the need for the two-holed passenger side knuckle.

    http://www.hermtheoverdriveguy.com/id83.htm

    I know, it's not as strong as the two-holed knuckle and oversized TREs, but for as much trail use as my Jeep is going to see, I'm playing the odds. Time will tell if I chose wisely! :D
     
    w3srl, Jan 25, 2005
    #11